EK Water Blocks EK-FC7970 - Acetal + Nickel CSQ Bedienungsanleitung PDF herunterladen

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 21

of June, 2012. Revision 1.0

Installation and mounting manual for EK-FC7970 CSQ water block

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION. Sample picture of AMD Radeon HD 7970 graphics card (PCB 109-C38637-00)

STEP 2: PREPARING YOUR GRAPHIC CARD.

1. REMOVING STOCK COOLER: Remove encircled screw on

the bracket (required only on certain models):

STEP 2 cont.: PREPARING YOUR GRAPHIC CARD

1 cont.. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink assembly

screws should be removed. There are 16 screws on the back of the graphic card.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing

all screws securing it to the board. Wipe off the remains (by using non–abrasive

cloth or

qtip

, as shown on sample photo) of the original thermal compound until

the components and circuit board are completely clean. EKWB recommends the

use of denatured alcohol for removing TIM leftovers.

3. APPLYING THERMAL COMPOUND. Apply thermal

compound: lightly coat

AMD

GPU chip with for example

Arctic Cooling MX-2 ™ or MX-4 ™ thermal grease. EKWB

recommends to apply thermal grease in cross form for

best performance (see sample picture).

4. CUTTING THERMAL PADS. Your block comes with thermal pads, some of which are already pre-cut. Others have

to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and drivers. PLEASE REMOVE

THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION.

Replacement thermal pads: 1x Thermal Pad B – 0.5mm (75x50mm), Thermal Pad A – 1mm (100x16mm).

STEP 3: INSTALLING WATER BLOCK

1. PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers on chips match size of thermal pads. EKWB made sure users have more than

enough pads to cover all surfaces that need to be covered to make block fully functional). EKWB recommends using small drops of electrically non-conductive (for

example: Arctic Cooling MX-2 ™, MX-4 ™ or GELID GC-Extreme™) thermal grease on each phase regulator (that is being covered with thermal pad) in order to even

further improve the thermal performance of the EK-FC7970 CSQ series water block.

1: Thickness 0.5mm

(for memory IC):

2: Thickness 0.5mm

(for VRM Driver & MOSFET IC):

3: Thickness 1mm (for I/O VRM):

1 2

Inhaltsverzeichnis

Seite 1

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use.

Seite 2

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use.

Kommentare zu diesen Handbüchern

Keine Kommentare

EK Water Blocks EK-FC7970 - Acetal + Nickel CSQ Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Computer Flüssigkeitskühlung EK Water Blocks EK-FC7970 - Acetal + Nickel CSQ herunter. EK Water Blocks EK-FC7970 - Acetal + Nickel CSQ [de] [es] [fr] [ja] [pt] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computer Flüssigkeitskühlung EK Water Blocks EK-FC7970 - Acetal + Nickel CSQ