EK Water Blocks 3831109840597 Handbuch PDF herunterladen

Revision 1.0. Released on 2

of October, 2012.

Installation and mounting manual for EK-BAY DCP 2.2 Combo Reservoir

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

3. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION. Sample picture of EK-BAY DCP 2.2 Combo Reservoir

STEP 2: INSTALLING EK-DCP 2.2 WATER PUMP TO THE RESERVOIR

Take your reservoir out of the original packaging and place it on a flat, clean surface with the front facing downwards. Proceed with the following steps:

1) Remove the three out of four original EK-DCP 2.2 pump screws from the pump using Philips head screwdriver.

2) Install o-ring (OR 20x2) gasket into the groove milled in EK-BAY DCP 2.2 Combo Reservoir acetal body. Make sure the gasket is positioned correctly in

the groove.

3) Place the pump onto the main reservoir body and insert the three (3) M3x18 DIN7984 screws which are provided with the reservoir. EK recommends user

to screw-in the screws slightly using your thumbs for the screws prior to tightening them with the enclosed 2mm Allen key.

4) Tighten the screws using 2mm Allen Key.

STEP 3: MOUNTING THE RESERVOIR INSIDE YOUR COMPUTER CHASSIS:

This reservoir occupies two 5.25” drive bay expansion slots in your computer chassis. Free two slots in case they are already occupied with other

computer components such as optical- or hard disk drives:

1) Install anti-vibration rubber damper into each of the three slots on the sides of the reservoir

2) Place the reservoir in your

5.25" drive bay

with the front plate facing outwards

3) Secure the reservoir to the drive bay cage using the enclosed M3x4 DIN7985 screws and Philip head screwdriver.

M3x4 DIN7985 screw

EK-BAY DCP 2.2

Combo Reservoir

Allen key 2mm

Screw M3x18 DIN7984

OR 20x2 gasket

EK-DCP 2.2 water pump

M3 BAY anti-vibration

rubber damper

STEP 1: Remove the marked screws

1 2

Water out 2

Inhaltsverzeichnis

Seite 1

Revision 1.0. Released on 2nd of October, 2012. Installation and mounting manual for EK-BAY DCP 2.2 Combo Reservoir This produc

Seite 2 - Water out

Revision 1.0. Released on 2nd of October, 2012. STEP 4: CONNECTING YOU RESERVOIR Connect two G1/4 threaded fittings to t

Kommentare zu diesen Handbüchern

Keine Kommentare

EK Water Blocks 3831109840597 Handbuch

Stöbern Sie online oder laden Sie Handbuch nach Computer Flüssigkeitskühlung EK Water Blocks 3831109840597 herunter. EK Water Blocks 3831109840597 Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computer Flüssigkeitskühlung EK Water Blocks 3831109840597