EK Water Blocks EK-FC5X0 GTX GW Handbuch PDF herunterladen

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 15

of April, 2011.

Installation and mounting manual for EK-FC5x0 GTX GW backplate

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

STEP 1: GENERAL INFORMATION. Sample picture of Gainward/Palit GeForce 570/580 GTX graphics card.

STEP 2: PREPARING YOUR GRAPHIC CARD GEFORCE 5x0 GTX CARD

STEP 3: APPLYING THE THERMAL PADS

EK-FC5x0 GTX GW backplate is very easy to install. First install EK-FC5x0

GTX GW water block according to it’s manual. If you have it already

installed, please check below which mounting screws for water block are to

be left in their position. Please remove encircled screws marked with

arrow!

In order to enhance the cooling performance of the EK-FC5x0 GTX GW

please install – as shown in picture below – three 1.5mm thick thermal

pads on the extruded stub on the backplate itself.

STEP 3: ATTACHING EK-FC5x0 GTX GW BACKPLATE

Take enclosed mounting screws and install them as shown on picture below. EKWB recommends users to start with M3x9 screws. Afterwards fasten

remaining M3x12 screws (HINT: do not tighten screws until they are all positioned in their mounting holes). Please note that nuts with washers

must be used on M3x10 screws in order to provide proper connection of PCB and backplate. Backplate has milled in standoffs, so there is no fear of

overtightening the screws. Nevertheless, do not exaggerate with screwing force as there is no need for it.

(Please note that EKWB holds no responsibility of any kind if assembly is not made by instructions. This applies also for all products that are not out

of EKWB production line. Users must by all means also consider instructions that are being made for proper use of FC blocks.)

REQUIRED TOOLS AND MOUNTING SCREWS:

3 x screws M3x9 7991DIN 3 x M3x12 7991DIN 3 x M3 nut 6 x M3 PVC washers 2mm allen key

Use enclosed allen key on

screws to attach backplate.

M3x9 screws

M3x12 screws

M3 nut

VERY IMPORTANT NOTICE: Do not ever bend or push backplate on this edge

towards PCB. This edge is unsupported. However backplate itself is rigid enough to

prevent any unnecessary contacts. Nonetheless we strongly recommend users to

check for contacts prior to inserting cards back in slots.

Thickness 1.5mm

Note: Dimensions below are scaled!

M3x12 screw

PVC washer

Inhaltsverzeichnis

Seite 1

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 15th of April,

Weitere Dokumente für Computer Flüssigkeitskühlung EK Water Blocks EK-FC5X0 GTX GW

Um das Dokument anzuzeigen EK Water Blocks EK-FC5X0 GTX GW Handbuch

EK Water Blocks EK-FC5X0 GTX GW Handbuch (2 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

EK Water Blocks EK-FC5X0 GTX GW Handbuch

Stöbern Sie online oder laden Sie Handbuch nach Computer Flüssigkeitskühlung EK Water Blocks EK-FC5X0 GTX GW herunter. EK Water Blocks EK-FC5X0 GTX GW Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Computer Flüssigkeitskühlung EK Water Blocks EK-FC5X0 GTX GW

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computer Flüssigkeitskühlung EK Water Blocks EK-FC5X0 GTX GW