EK Water Blocks 3831109856024 Handbuch PDF herunterladen

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 17

of August, 2011. Revision 1.0

Installation and mounting manual for EK-FC570 GTX SE water block

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box or our home page.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings. The use of an algaecide and corrosion inhibitors is always recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION. Sample picture of GeForce 570 GTX HD graphics card (PCB NVA-P1263)

STEP 2: PREPARING YOUR GRAPHIC CARD.

1. REMOVING STOCK COOLER: Remove encircled screw on

the bracket (required only on certain models):

STEP 2 cont.: PREPARING YOUR GRAPHIC CARD

1 cont.. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink assembly

screws should be removed. There are 17 screws on the back of the graphic card.

2. CLEANING THE PCB. Carefully detach the original heat sink after removing all

fasteners securing it to the board and bracket. Wipe off the remains (by using

non–abrasive cloth or Q-tip, as shown on sample photo) of the original thermal

compound until the components and circuit board are completely clean. EKWB

does not recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND. Apply thermal

compound: lightly coat

nVidia GF110

GPU chip with for

example Arctic Cooling MX-2 ™ or MX-4 ™ thermal

grease. EKWB recommends to apply thermal grease in

cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. Your block comes with thermal pads, some of which are already pre-cut. Others have

to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and inductors (chokes).

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION.

STEP 3: INSTALLING WATER BLOCK

1. PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers on chips

match size of thermal pads. EKWB made sure users have more than enough pads to cover

all surfaces that need to be covered to make block fully functional). EK recommends using

small drops of electrically non-conductive (for example: Arctic Cooling MX-2 ™ or MX-4 ™)

thermal grease on each phase regulator (that is being covered with thermal pad) in order to

even further improve the thermal performance of the EK-FC570 GTX SE series water block.

2. PLACING GPU REINFORCE PLATE ON PCB. Place metal reinforce and washer on

PCB as shown on picture below and screw it in with enclosed M3x4 screws. Please

use encased PVC washers under each screw. Make sure you use fasten screws

equally and do not use too much force.

Orientation

of reinforcer

is important!

M3x4

screw

PVC washer

Thickness 1mm (for memory)

Thickness 0.5mm (for VRM MOSFETS and inductors (R30)

Washer

1 2

Inhaltsverzeichnis

Seite 1

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use.

Seite 2

All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use.

Kommentare zu diesen Handbüchern

Keine Kommentare

EK Water Blocks 3831109856024 Handbuch

Stöbern Sie online oder laden Sie Handbuch nach Computer Flüssigkeitskühlung EK Water Blocks 3831109856024 herunter. EK Water Blocks 3831109856024 Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computer Flüssigkeitskühlung EK Water Blocks 3831109856024